1964 Chevrolet C 10 on 2040-cars
Pittsburgh, Pennsylvania, United States
|
This truck wears all the sheet metal it was equipped with from Chevrolet in 1964 cab corners inner rockers outer rockers this is a nice solid unmolested truck. This honey for the money has a 6 cylinder 3 speed on the column. This truck lived its life in South Carolina and was garage kept needs nothing has been tuned up new wires spark plugs cap rotor points fuel pump fuel tank sending unit brakes wheel cylinders brake hoses master cylinder and 4 new tires. It runs out great new wood in bed paint not new but represents well no rust I that I can see any wear. I have the truck for sale locally so I can pull anytime Thanks for looking any questions you can call me at 412 480 8566 Randy
|
Chevrolet C-10 for Sale
1960 chevy apache
1966 chevrolet c10 short bed fleetside air bagged patina shop truck no rat
1987 silverado c10/r10 chevy classic truck rare original 2nd owner swb
Chevrolet c10 white with 350 motor and rebuilt 700r trans(US $5,500.00)
Bagged 1965 chevy swb(US $15,000.00)
1972 chevy c-10 shortbed fleetside 350/350 auto
Auto Services in Pennsylvania
Valley Tire Co Inc ★★★★★
Trinity Automotive ★★★★★
Total Lube Center Plus ★★★★★
Tim Howard Auto Repair ★★★★★
Terry`s Auto Glass ★★★★★
Spina & Adams Collision Svc ★★★★★
Auto blog
Camaro spy shots show subtly different grille, front fascia
Sun, 03 Feb 2013It looks like there some changes in store for the Chevrolet Camaro - the only thing is that we just don't know what Chevy has up its sleeve. Looking at these spy shots, we'd initially be inclined to think that there is just a minor facelift or a new special edition, but upon closer inspection, there are a few oddities about this car that definitely have us intrigued.
The most obvious difference on this prototype is the slightly restyled front fascia with a smaller lower air inlet and the two-bar grille. Then we get to some of the car's mysterious details. For starters, this fascia has the SS vent above the grille, but it looks to be blocked off. Granted this could just be a one-off piece used for testing. What really piqued our interest was at the rear of the car where it has quad exhaust outlets that are used on the ZL1. Could this be the LS7-powered Camaro that we reported on back in December?
At this point, your guess is as good as ours as to what we're looking at here, so let us know in the comments what you think this could be.
Supercharged 2015 Chevy Corvette Z06 takes the C7 beyond the ZR1
Mon, 13 Jan 2014
The Z06 is just about everything we got in the last ZR1, but better.
After a bright-yellow false start, here is the real thing: the fourth-generation, 2015 Corvette Z06. If Chevrolet makes a ZR1 version of the C7 Corvette, it's going to be absolutely mega, because the Z06 is just about everything we got in the last ZR1, but better.
GM recalls 8,500 Chevrolet Malibu models for rear suspension glitch
Mon, 04 Feb 2013According to a letter from General Motors to the National Highway Traffic Safety Administration, flaws in the build process of the 2013 Chevrolet Malibu have led to the recall of 8,519 cars. Units built between December 6, 2011 and January 15, 2013 may have been assembled with rear suspension cradles that had insufficient torque applied to certain bolts. That out-of-spec assembly could lead to issues ranging from slight noises to a loss of vehicle control.
The problem was first noticed in December of last year by a GM test fleet driver and eventually tracked back to the improperly torqued bolts on the suspension cradle assembled through July 2012 by a supplier located not too far from the Malibu's Detroit/Hamtramck Assembly Plant. Since an official NHTSA recall notice has not been issued yet, it isn't clear whether or not Detroit-built Malibus were the only ones affected (the 2013 Malibu is also built at GM's Fairfax Assembly Plant in Kansas City, Kansas). Dealers will fix the problem by inspecting vehicles for proper torque specs, retightening if not within specs and, in some cases, perform a rear-wheel alignment.