1972 Chevy Truck on 2040-cars
Grafton, Ohio, United States
|
I am listing my 1972 Chevy C10 for sale. This truck is restorable and needs some body work. I am a machinist by trade, so I machined and built a custom 400 small block Chevy engine for a street performance vehicle. My intentions were to restore the truck, but due to my divorce I had to install this engine in the truck to get it on the road and out of her driveway. This engine is a bit much for this truck but it has worked out well and this thing moves! The base of the engine is a highly sought after 2 bolt 509 casting, small block 400 that has a higher nickel content than other 400's. It is bored and honed .030." The cylinder heads are Brodix aluminum castings that I ported, drilled the proper steam holes, milled, and put a performance valve job on before assembling. They are 187cc volume intake runners after the port work and flow well. ARP head bolts clamp the heads to the block. Comp Cams roller valve springs, retainers, locators, locks, guide plates, pushrods, etc. The camshaft is an Erson custom billet hydraulic roller with 228/236 @ .050" and has .540" lift. I got the upgraded option that has a pressed on and pinned steel gear for the distributor ($75 extra.) No bronze or expensive composite gear required. The lifters are of the highest quality, Morel hydraulic rollers. This company (Morel) builds lifters for the top fuel cars and they make the best available today. They are over $600 a set. The timing chain is a 9 keyway billet true roller with a bronze wear plate and a roller cam button. The timing cover is a reinforced steel version to limit cam walk. Crower stainless steel 1.5 ratio full roller rocker arms. Edlebrock EPS intake manifold, 670 cfm 4 barrel Holley Avenger truck carburetor, MSD HEI Street fire distributor and wires, and NGK plugs round out the top end. It also has a new water pump, alternator, and starter. This truck has the power steering option and it works great. The crankshaft was magnafluxed, turned 10/10 on the rods and mains, knife-edged, balanced, has Clevite bearings and is retained by ARP main studs. The Pioneer 8" balancer is also a new and is for an external balance set up. I magnafluxed, balanced, polished, and reconditioned a set of 5.7 small block rods with ARP bolts. Pistons are Keith Black dished hypereutectics and total seal rings that I filed to fit the bores properly. Oiling is with a Melling M55HV high volume/high pressure pump, a heavy duty pump shaft, and has a ARP pump stud holding it in place. A Milodon steel pickup with Milodon 7qt low profile oil pan. I have done two oil changes to this truck because I have only put 780 miles on it since I installed this motor in August 2013. I have only used Brad Penn green oil in it and Fram HP4 racing filters. I have the compression ratio set at 9.7:1 for a pump gas friendly set up. If someone wanted to bracket race this engine, it would be a great candidate. The parts in this engine are overkill for a street rod and I did that so it would be a durable power plant. I have over $5000 in parts in this engine and I have receipts for most of it. With the labor of building, machining and porting a custom engine like this it would cost in the $7-8000 range through a shop. Probably more after they mark up the parts. You have to keep in mind this is not thrown together. These parts were a hand picked proven combination by a professional and blueprinted accordingly. I did not dyno this engine but I have used similar combinations before and depending on compression, they have made 450hp+ and over 500ft lbs of torque on pump gas all day long. It has ample piston to valve clearance and I set it up this way so the heads could be milled more in case I wanted to push this thing to the edge. It is also lowered with Hotchkis springs and shocks. 2 1/2" in the front and 3" in the rear to give it an even stance. There is a larger sway bar on the front with urethane parts. The truck handles well. New front disk brakes and rotors, wheel bearings, ball joints, tie rods, idler arm, and center link. Shifting the gears is a turbo 350 and a 12 bolt truck rear-end out back. Dual exhaust all the way back and it has the stock truck manifolds that I port matched to the heads as well. I have many extras to go along with it. Including a Harwood fiberglass show series 3" cowl, bolt on hood and the lightweight springs for it, I have extra door glass for both doors, 4 extra vent windows, another instrument panel cluster, and some other miscellaneous items. All of the gauges work and it has a tachometer that is not stock as well. Everything works on this truck like the blinkers, lights, wipers, heat, etc. The interior is in pretty good shape and the bucket seats are very comfortable. This truck was originally optioned with the 350 4 barrel set up. The truck is rough but has potential. The gem is the 400 small block and the truck essentially comes with it. I don't have the time or patience to do the body work at this time. So I'm parting ways with it. I require the buyer to handle all shipping costs and for the truck to be paid in full before the title and vehicle are exchanged. WINNING BIDDER IS RESPONSIBLE FOR PICK UP/SHIPPING, TRUCK IS SOLD AS IS WHERE IS WITH NO WARRANTY. |
Chevrolet C-10 for Sale
Beautiful candyapple finish, 383 cid w/450hp, professionally built show truck!(US $29,995.00)
1978 chevrolet c-10(US $9,500.00)
C-10 short bed
Custom 1962 1/2 ton chevy shortbed stepside truck
1972 chevrolet c10 pickup base 5.7l
1970 chevrolet c-10 built by the roadster shop, award winner(US $77,500.00)
Auto Services in Ohio
Zig`s Auto Service ★★★★★
Zeppetella Auto Service ★★★★★
Willis Automobile Service ★★★★★
Voss Collision Centre ★★★★★
Updated Automotive ★★★★★
Tri C Motors ★★★★★
Auto blog
Why the Corvette is Chevrolet's billion-dollar baby
Thu, 28 Feb 2013Edmunds has worked up a piece that tries to figure out just how much the global Chevrolet Corvette economy is worth, a spitballed guesstimate putting the number at more than $2.5 billion with the proviso that the number is probably low. It starts by taking Corvette's new car sales of 14,132 units last year, which would equate to $714,725,900 (including destination) assuming ever car sold was a base coupe with no options. In the final tally, a little extra padding gets that number up to $750,000,000.
But that's not all. Consider this: Many of the almost 1.4 million Corvettes produced over the model's history are still on the road. There are new parts being produced and aftermarket companies like Mid-America Motorworks deaing business, that single Illinois company doing more than $40 million a year in sales. There are the Corvette events large and small, restorers who do nothing but Corvettes, salvage yards that deal only in used Corvette parts and the Corvette magazines where owners find all this stuff.
And then there are the Corvette-themed tchotchkes, every single one of which provides a tiny contribution to the huge licensing royalties that General Motors collects every year. The article admits there's no way to come to an accurate number, but it just goes to show how valuable one specific model can be to a company.
Ford, Toyota clean up in Best Car For The Money Awards
Fri, 22 Feb 2013The U.S. News Best Cars for the Money Awards picks winners by looking at the average transaction price, five-year total cost of ownership, the regard a car has from the automotive press, reliability figures from J.D. Power and Associates and safety data from the National Highway Traffic Safety Administration and the Insurance Institute for Highway Safety. The result, according to the magazine, is "the best combination of critical acclaim and long-term value."
Ford nabbed six of the 21 categories that received awards this year, the Focus, Fusion, Fusion Hybrid, Taurus, Escape and Edge getting trophies. Toyota and its Lexus and Scion sub-brands took another five, the Tacoma and Tundra owning the two categories given to pickup trucks. The other ten awards were split between Honda with three, Buick with two, and one each for Subaru, BMW, Hyundai, Chevrolet and Mazda.
Follow the link to see all the winners and read about why they were chosen.
GM tinkering with Silverado, Sierra model mix amidst strong early sales
Mon, 04 Nov 2013Variety, as they say, is the spice of life. That's a lesson that is currently being taught to General Motors, because despite a strong showing from its 2014 Chevrolet Silverado and GMC Sierra, the General's pickup sales still can't best those of cross-town rival Ford.
With 59,163 trucks moved, GM fell just over 1,000 units short of toppling Ford, and one of the main reasons for that, according to GM's chief sales analyst, was due to a lack of variety in the engines and body styles available on dealer lots. "We are still over-weighted toward crew-cab V8 trucks. Our light-duty mix will moderate over time as our launch progresses," said Kurt McNeil.
Loading dealers with the popular combination of the 5.3-liter V8 and the four-door, Crew Cab body style was intentional during the truck's launch, but as supplies of leftover 2013 models, which are being sold at heavy incentives, are beginning to wane, both budget-conscious and high-dollar buyers are looking elsewhere instead of at the volume model pickups.