1995 Chevrolet K2500 Silverado Extended Cab Pickup 2-door 6.5l on 2040-cars
Alma, Kansas, United States
1995 Chevy Silverado 3/4 ton ext cab, 6.5 Turbo Diesel, 5 speed transmission, B&W turnover gooseneck hitch, rebuilt engine installed at 186800 miles with heavy duty thick military block, many new parts, front bearing hubs, new front brakes with calipers and rotors and lines, SSDiesel cooling system upgrade with 97 water pump duel thermostat cross over tube, cold air intake, PMD relocation kit new from SSDiesel, engine oil cooler hoses, cold air intake, starter, alternator, radiator, glow plugs, glow plug controller with rebuilt glow plug wire harness, new clutch, clutch slave cylinder and clutch master cylinder, turbo has been replaced 8 yrs. ago along with vacuum pump and waste gate solenoid.
|
Chevrolet C/K Pickup 2500 for Sale
- 1995 chevy k2500 hd with 2nd set of doors(US $3,800.00)
- 1979 chevrolet truck c20 2500 3/4 ton 2 wd only 59k miles!!!(US $3,495.00)
- 86 chevrolet 3/4 ton 4x4 with sno-way plow(US $5,500.00)
- 1985 chevrolet k20 4wd longbed with toolbox(US $3,000.00)
- Chevrolet k2500 duramax turbo diesel 4x4(US $8,000.00)
- 1999 chevrolet k2500 ls standard cab pickup 2-door 7.4l(US $10,000.00)
Auto Services in Kansas
Whitey`s Auto Repair ★★★★★
Westlink Auto Service ★★★★★
Unlimited Auto Sales ★★★★★
Starbird`s Collision Experts ★★★★★
Rick`s Custom Exhaust & Auto Repair ★★★★★
Pit Stop Automotive ★★★★★
Auto blog
Final C6 Corvette built in Bowling Green
Fri, 01 Mar 2013With all of the attention given to the 2014 Chevrolet Corvette Stingray lately, you could be forgiven for thinking that it's already well along in production, yet tooling up for the new C7 has only just begun. In fact, production of the outgoing C6 generation in Bowling Green, Kentucky just halted on Thursday.
As the C6 has aged, production numbers have predictably ebbed along with demand, but this year, the addition of the 427 and 60th anniversary models resulted in an uptick in vehicles built - this, despite a model year shortened by around 25 percent to accomodate the new model changeover. The final C6 Corvette ever, No. 13,466 built this year, was a white 427 Convertible destined for the General Motors Heritage Center museum. The car's 7.0-liter V8 heart was assembled by Corvette chief engineer Tadge Juechter himself.
In total, Bowling Green pushed out 215,100 C6 Corvettes over nine years. If you're still a C6 fan at heart and are hoping to get a good deal on a phase-out model, step lively - Chevrolet reportedly had about 6,100 unsold units, which Autoweek suggests is good for around five and a half months of supply at the model's current sales rates. Given that demand will likely slacken even further as the C7 draws closer, that should be a big enough stockpile to keep dealers satisfied until 2014 Stingrays begin showing up on their forecourts in December.
Veyron and C7 Corvette join cast of Transformers 4
Wed, 29 May 2013Like the Fast & Furious franchise, the Michael Bay-directed series of Transformers movies has become known as much for its bad acting as its impressive lineup of cars. As filming just started for Transformers 4, Bay's website has confirmed two new cars for the next installment as well as a makeover for everyone's favorite tractor trailer hero, Optimus Prime.
Joining the cast of T4 are a "race-inspired" Chevrolet Corvette Stingray and a Bugatti Veyron Grand Sport Vitesse. While Bay's website did not supply names for either car, Bugatti is reporting on its Facebook page that the Veyron will join the Autobots. Speaking of the good guys, top Autobot Optimus Prime is getting an all-new body based on a Western Star with a gaudy appearance that was seemingly inspired by Trick My Truck - right down to the six smoke stacks and side pipes!
Experimental mid-engine XP-819 Corvette going up for auction
Sun, 17 Feb 2013It seems to be commonplace that when a new Corvette is in development, rumors swirl about a possible mid-engine layout. As is the case of Chevy's most recent C7 Corvette, these rumors never pan out.
In any case, the idea for a 'Vette with an engine mounted behind the driver can probably all be traced back to a single car, the 1964 XP-819 prototype. Built as an "engineering exercise" back in 1964, the prototype was designed with a rear-mounted engine. History tells us that the idea of a rear-engine Corvette fizzled, and the XP-819 was eventually cut up into pieces and stored at a shop in Daytona Beach, FL.
After sitting for untold years, a restoration project started on the car, and while it isn't yet fully completed, the current owner of the car, Mid America Motorworks, will have the car on display at the 2013 Amelia Island Concours d'Elegance as a "driveable chassis" with hopes of having a fully completed car ready to bring to next year's show.