1991 Chevy 1 Ton 4 X 4 Crew Cab Dually on 2040-cars

Auto blog

Chevrolet Malibu gets across-the-board price cuts, hopes to dig out of slump

To say that things aren't going well for the newly redesigned 2013 Chevrolet Malibu is a pretty sizable understatement. Reports have been swirling about the Malibu getting an emergency design refresh, less than a year after its introduction, as well as having its production at the Fairfax Assembly Plant halted twice already this year for excessive inventory. Now, Motor Trend is reporting that the midsize sedan will be receiving price drops across the board ranging from $300 on a number of models up to $770 on the 1LT trim; offsetting some of MSRP drop, though, the destination charge has increased from $760 to $810.
Without destination, the entry-level Malibu LS now starts at $21,995, which is still about $300 more than a Honda Accord and about $300 less than the segment's top-selling Toyota Camry. This new pricing also drops the price of the Eco, 2LT and 3LT trims by $300. The LTZ trim has dropped by $415, meaning that the Malibu's top dog now starts at just under $30,000, excluding destination.
Here are the new starting prices for all eight of the Malibu trim levels compared to the previous prices for the 2013 model year (including destination):

Experimental mid-engine XP-819 Corvette going up for auction

It seems to be commonplace that when a new Corvette is in development, rumors swirl about a possible mid-engine layout. As is the case of Chevy's most recent C7 Corvette, these rumors never pan out.
In any case, the idea for a 'Vette with an engine mounted behind the driver can probably all be traced back to a single car, the 1964 XP-819 prototype. Built as an "engineering exercise" back in 1964, the prototype was designed with a rear-mounted engine. History tells us that the idea of a rear-engine Corvette fizzled, and the XP-819 was eventually cut up into pieces and stored at a shop in Daytona Beach, FL.
After sitting for untold years, a restoration project started on the car, and while it isn't yet fully completed, the current owner of the car, Mid America Motorworks, will have the car on display at the 2013 Amelia Island Concours d'Elegance as a "driveable chassis" with hopes of having a fully completed car ready to bring to next year's show.

Final C6 Corvette built in Bowling Green

With all of the attention given to the 2014 Chevrolet Corvette Stingray lately, you could be forgiven for thinking that it's already well along in production, yet tooling up for the new C7 has only just begun. In fact, production of the outgoing C6 generation in Bowling Green, Kentucky just halted on Thursday.
As the C6 has aged, production numbers have predictably ebbed along with demand, but this year, the addition of the 427 and 60th anniversary models resulted in an uptick in vehicles built - this, despite a model year shortened by around 25 percent to accomodate the new model changeover. The final C6 Corvette ever, No. 13,466 built this year, was a white 427 Convertible destined for the General Motors Heritage Center museum. The car's 7.0-liter V8 heart was assembled by Corvette chief engineer Tadge Juechter himself.
In total, Bowling Green pushed out 215,100 C6 Corvettes over nine years. If you're still a C6 fan at heart and are hoping to get a good deal on a phase-out model, step lively - Chevrolet reportedly had about 6,100 unsold units, which Autoweek suggests is good for around five and a half months of supply at the model's current sales rates. Given that demand will likely slacken even further as the C7 draws closer, that should be a big enough stockpile to keep dealers satisfied until 2014 Stingrays begin showing up on their forecourts in December.