9 Passenger Conversion Van, Low Miles!! We Finance! Loaded! #1 Van Dealer! on 2040-cars

Auto blog

2014 Chevrolet Silverado and GMC Sierra debut all-new designs, three new engines

General Motors has finally dropped the curtain on the 2014 Chevrolet Silverado and 2014 GMC Sierra. Both trucks have undergone substantial revisions with updated versions of the company's 4.3-liter V6, 5.3-liter V8 and 6.2-liter V8 engines. In a shot across the bows of both Ford and Chrysler, GM says it won't use a V6 engine adapted from passenger car applications. Instead, it developed the 4.3-liter engine based on its proven truck-duty architecture.
All three mills will boast direct injection fuel systems as well as a new cylinder head design. Combined with a revised piston, the new engines feature a smaller combustion chamber with a compression ratio of 11:1 or higher depending on the application. Cylinder deactivation and continuously variable valve timing are all part of the recipe, and each engine is paired with a six-speed automatic transmission with auto grade breaking. So far, no fuel economy or horsepower figures have been released, though GM says the new engines will best their predecessors in both areas.
Outside, the trucks feature a number of enhancements to reduce drag and wind noise, and GM claims both the Silverado and Sierra will offer buyers some of the quietest cabins in the class. Extended cab models now feature front-hinged rear doors to allow easier access to the back passenger area, and Crew Cab buyers can now select between a five-foot, eight-inch bed or a six-foot, six-inch bed. Buyers with a mind toward going off road will also rejoice in the return of the Z71 package, complete with Rancho shocks, front tow hooks and additional under-body protection.

More Corvette Stingray Factoids: Vanishing panel gaps and 26-mpg LT1

During January's Detroit Auto Show, we managed a longer than expected wandering tag-team interview with C7 Corvette chief engineering exec Tadge Juechter (pictured above), and LT1 engine boss Jordan Lee (pictured below). They are, quite honestly, two of the very nicest bigshot lads to ever walk the engineering corridors of an American manufacturer. Both are enthralled by what they're doing for a day job. So are we.
We've followed the pre-sale anticipation for the Chevrolet C7 Corvette Stingray like an Oreck vacuum yanking every speck of dirt from a well-trampled carpet. Everything is reportable and contains a grain of further knowledge about this dramatically important and cheered-for car, as it continues to be pressured into representing all that is superior about the American dream. The Corvette wears one heavy cloak.
So, most of what was talked about has been expertly reported already right here on Autoblog. But, looking through our notes again, both Jeuchter and Lee added facts to the buzzing mix.

GM recalls 8,500 Chevrolet Malibu models for rear suspension glitch

According to a letter from General Motors to the National Highway Traffic Safety Administration, flaws in the build process of the 2013 Chevrolet Malibu have led to the recall of 8,519 cars. Units built between December 6, 2011 and January 15, 2013 may have been assembled with rear suspension cradles that had insufficient torque applied to certain bolts. That out-of-spec assembly could lead to issues ranging from slight noises to a loss of vehicle control.
The problem was first noticed in December of last year by a GM test fleet driver and eventually tracked back to the improperly torqued bolts on the suspension cradle assembled through July 2012 by a supplier located not too far from the Malibu's Detroit/Hamtramck Assembly Plant. Since an official NHTSA recall notice has not been issued yet, it isn't clear whether or not Detroit-built Malibus were the only ones affected (the 2013 Malibu is also built at GM's Fairfax Assembly Plant in Kansas City, Kansas). Dealers will fix the problem by inspecting vehicles for proper torque specs, retightening if not within specs and, in some cases, perform a rear-wheel alignment.