1965 Chevelle Malibu Convertible...283 Engine...automatic on 2040-cars
Wagram, North Carolina, United States
I purchased this car from a classic car dealer in AZ about 2 years ago. They told me it has spent most of it's life there so rust is not an issue. Since buying the car, I have replaced the tires, recored the radiator and put a new Edelbrock 4bbl carb & manifold on the engine. The carb that came with the car was way too big ror a 283. I was told the engine and trans are original to the car and both have been rebuilt. The car has had a decent restoration including paint, interior, chrome, stainless trim etc. I would guess the restoration to be about 3 years ago. It is as clean under the hood and frame as the exterior. There are some minor issues I haven't gotten to such as the horn doesn't work, the wipers and radio only work when they want to, the door glass does not roll all the way up, the zipper on the rear window is separating from the fabric and there is a small trans fluid leak at the speedo connection. The car is being offered as is, where is and the buyer is responsible for all transportation costs. Thanks for looking. |
Chevrolet Malibu for Sale
- 1972 chevelle 350 four barrel, no rust, california car ( collector vehicle)
- 1967 chevelle convertible 327 all original 55k miles
- 08 xm radio heated leather adjustable pedals auxiliary input sunroof tint
- Front wheel drive sunroof wood trim two tone color interior we finance
- 1979 chevrolet malibu v8
- 1972 chevrolet chevelle
Auto Services in North Carolina
Willmon Auto Sales ★★★★★
Westend Auto Service ★★★★★
West Ridge Auto Sales Inc ★★★★★
Valvoline Instant Oil Change ★★★★★
USA Automotive ★★★★★
Triangle Window Tinting ★★★★★
Auto blog
GM recalls 8,500 Chevrolet Malibu models for rear suspension glitch
Mon, 04 Feb 2013According to a letter from General Motors to the National Highway Traffic Safety Administration, flaws in the build process of the 2013 Chevrolet Malibu have led to the recall of 8,519 cars. Units built between December 6, 2011 and January 15, 2013 may have been assembled with rear suspension cradles that had insufficient torque applied to certain bolts. That out-of-spec assembly could lead to issues ranging from slight noises to a loss of vehicle control.
The problem was first noticed in December of last year by a GM test fleet driver and eventually tracked back to the improperly torqued bolts on the suspension cradle assembled through July 2012 by a supplier located not too far from the Malibu's Detroit/Hamtramck Assembly Plant. Since an official NHTSA recall notice has not been issued yet, it isn't clear whether or not Detroit-built Malibus were the only ones affected (the 2013 Malibu is also built at GM's Fairfax Assembly Plant in Kansas City, Kansas). Dealers will fix the problem by inspecting vehicles for proper torque specs, retightening if not within specs and, in some cases, perform a rear-wheel alignment.
Why does the Corvette Stingray have so many vents? Here's why
Sun, 27 Jan 2013Just looking at the new 2014 Chevrolet Corvette Stingray, it's not hard to see that the car's design was created with aerodynamics at the forefront, but Chevrolet designers point out exactly what went into designing the iconic coupe in a pair of recently released videos. The videos show the Corvette going through early design phases, including clay models and wind tunnel tests, as well as talking to the car's chief engineer, Tadge Juechter.
Both videos help explain various aspects of the C7 Corvette, but it's the aero tuning of the car that is most interesting. This includes extra attention paid to the lower air dam and vented hood to help reduce drag and lift, while the rear quarter inlets are for differential and transmission cooling. Juechter said that some of these aero-tuned elements were inspired from GM's involvement in racing.
If you have about five minutes and you can't get enough information about the new 'Vette, then check out the videos posted below.
UAW to vote on strike at Kentucky Corvette plant
Tue, 08 Apr 2014The current wait time for a new Chevrolet Corvette Stingray is well, not short. With word of a strike at the Bowling Green, KY factory responsible for seventh-generation sports car, though, that wait time could end up growing substantially.
Now, a strike is still a ways off. UAW Local 2164, which represents the 800 workers responsible for screwing the Corvette together, is set to vote on authorizing a strike today, but even if the employees give the action a go, it's far from a sure thing. According to The Tennessean, both regional and national union officials would need to put their stamp of approval on strike action.
"The membership has to vote to strike, but it's just a step in the process," said Gary Casteel, the UAW's Region 8 director and one of the people that would need to authorize a strike action. Casteel told The Tennessean, "It's purely a local situation, though. They are having some issues with the local management."