1958 Chevrolet Apache Pick Up, All Stock, Vintage Show Piece Or Dayly Driver. on 2040-cars

Auto blog

GM recalls 8,500 Chevrolet Malibu models for rear suspension glitch

According to a letter from General Motors to the National Highway Traffic Safety Administration, flaws in the build process of the 2013 Chevrolet Malibu have led to the recall of 8,519 cars. Units built between December 6, 2011 and January 15, 2013 may have been assembled with rear suspension cradles that had insufficient torque applied to certain bolts. That out-of-spec assembly could lead to issues ranging from slight noises to a loss of vehicle control.
The problem was first noticed in December of last year by a GM test fleet driver and eventually tracked back to the improperly torqued bolts on the suspension cradle assembled through July 2012 by a supplier located not too far from the Malibu's Detroit/Hamtramck Assembly Plant. Since an official NHTSA recall notice has not been issued yet, it isn't clear whether or not Detroit-built Malibus were the only ones affected (the 2013 Malibu is also built at GM's Fairfax Assembly Plant in Kansas City, Kansas). Dealers will fix the problem by inspecting vehicles for proper torque specs, retightening if not within specs and, in some cases, perform a rear-wheel alignment.

GM recalling over 243,000 crossovers over possible seat belt defect

2010 Buick Enclave - Click above for high-res image gallery
The summer of 2010's recall hit parade continues unabated today, with General Motors having just announced that it is asking 243,403 owners of its 2009-2010 Lambda crossovers to bring their three-row haulers in for inspection. The culprit? Second-row seat belts in select Buick Enclave, Chevrolet Traverse, GMC Acadia, and Saturn Outlook CUVs have "failed to perform properly in a crash."
According to GM, a second-row seat-side trim piece is to blame, as it can impede the upward rotation of the buckle after the seat is folded flat. As a result, if the buckle makes contact with the seat frame, cosmetic damage can occur, potentially requiring additional force to operate the buckle properly. So far, no great shakes, but in the process of applying that additional force, the occupant may push the buckle cover down to the strap, potentially revealing and depressing the red release button. As a result of this, the belt may not latch, or in certain cases, it may actually appear to be latched when, in fact, it isn't.

Final C6 Corvette built in Bowling Green

With all of the attention given to the 2014 Chevrolet Corvette Stingray lately, you could be forgiven for thinking that it's already well along in production, yet tooling up for the new C7 has only just begun. In fact, production of the outgoing C6 generation in Bowling Green, Kentucky just halted on Thursday.
As the C6 has aged, production numbers have predictably ebbed along with demand, but this year, the addition of the 427 and 60th anniversary models resulted in an uptick in vehicles built - this, despite a model year shortened by around 25 percent to accomodate the new model changeover. The final C6 Corvette ever, No. 13,466 built this year, was a white 427 Convertible destined for the General Motors Heritage Center museum. The car's 7.0-liter V8 heart was assembled by Corvette chief engineer Tadge Juechter himself.
In total, Bowling Green pushed out 215,100 C6 Corvettes over nine years. If you're still a C6 fan at heart and are hoping to get a good deal on a phase-out model, step lively - Chevrolet reportedly had about 6,100 unsold units, which Autoweek suggests is good for around five and a half months of supply at the model's current sales rates. Given that demand will likely slacken even further as the C7 draws closer, that should be a big enough stockpile to keep dealers satisfied until 2014 Stingrays begin showing up on their forecourts in December.