2006 Ford E-150 Telephone And Cable Business Ready!! All Inventory Included!!! on 2040-cars

Auto blog

NHTSA investigating Ford Fiesta for faulty door latches

The National Highway Traffic Safety Administration has opened a preliminary investigation on the 2011-2013 Ford Fiesta because the regulator has received 61 complaints from drivers, including one claim of an injury, about the doors on the subcompacts failing to latch and sometimes even flying open while driving. NHTSA has estimated that the problem could affect as many as 205,000 vehicles.
NHTSA is still gathering further data about the problem, but looking at the complaints so far, both front and rear doors appear to be potentially involved with the alleged failures. Among the reports, there are 12 claiming that the door opened while driving. Several also indicate the "Door Ajar" warning illuminating during this problem. The one purported injury happened when someone attempted to shut the door, and it bounced back.
Ford spokesperson Kelli Felker told Autoblog via email, "We are cooperating with NHTSA on this investigation, as we always do." Scroll down to read the report from NHTSA.

Ford opens the doors on its Swedish rally skunkworks

It's always amazing to see how different kinds of racecars are made. Formula One racers are often constructed in modern architectural marvels that hint at some of the cutting-edge technology going into the racing. Conversely, rallying is all about sliding around on a varied course as fast as possible, but it often leaves a vehicle caked in mud. So it makes some sense Olsbergs MSE, or simply (OMSE) rally car shop in Nynashamn, Sweden, shows technological sophistication in a more down-to-earth setting. It builds Ford Fiesta ST racers for Global Rallycross there, and this new video gives viewers a tour through the work.
Former rally driver Andreas Eriksson runs OMSE. These days instead of racing, he and the company's 46 employees are building Ford racers from scratch. A ton of work goes into constructing each one, and according to Eriksson, it takes 400 hours to complete each body. At times, things are so busy that some of the technicians live in the shop in apartments that are on premises. There's even a restaurant to keep them fed. Sadly the dyno room is empty during this visit, though.
By the time OMSE is done, a rallycross car might resemble a Fiesta ST on the outside, but as you see in the video, it's a completely different beast underneath. Check out the work it takes to build one of them, and scroll down to read more about it in the official release.

Ford confirms 1.5-liter EcoBoost four-cylinder engine for 2014 Fusion

Earlier this week, reports were swirling 'round the internet about the 2014 Ford Fusion getting a new 1.5-liter three-cylinder EcoBoost engine. That was... half correct. Ford today confirmed that the 2014 Fusion is, in fact, getting a new 1.5-liter EcoBoost mill, but it has four cylinders, not three.
The new 1.5-liter engine will be the fifth EcoBoost powerplant from Ford Motor Company. Initially to be built at the automaker's Craiova, Romania plant, it will also be offered in the Fusion's twin, the Mondeo, in other markets. This engine will debut at the Shanghai Motor Show next month, and the 1.5-liter is of particular importance in the Chinese market - there is significant tax relief in the People's Republic for vehicles powered by engines with a capacity of 1.5 liters or less.
At a media briefing Thursday, Ford declined to divulge exact power or fuel economy numbers, though Joe Bakaj, vice president of powertrain engineering, told Autoblog that power output should be similar to that of the current 1.6-liter inline-four, and that overall efficiency will be "better than the 1.6." Our earlier report stated that the 1.5-liter four will produce 177 horsepower and 177 pound-feet of torque - losses of 1 hp and 7 lb-ft versus the 1.6-liter engine. Ford states that the 1.5-liter four will feature many of the same technologies used on the company's 1.0-liter EcoBoost inline-three, including an integrated exhaust manifold that recaptures much of the engine's heat.