Xlt 4.2l Cassette Player Dual Air Bags Abs Anti-lock Brakes Tonneau Cover on 2040-cars

Auto blog

What next for Alan Mulally?

Alan Mulally has emerged as a hero when it comes to American manufacturing. He came to Ford in 2006 after serving as head of Boeing's commercial aircraft division, streamlined operations, sold off the costly elements of its Premier Automotive Group and saved Ford from having to be bailed out by the federal government like its cross-town rivals Chrysler and General Motors did. But as we reported mere days ago, he's widely expected to step down from the chief executive's office at Ford shortly.
So what's next for one of the most successful executives in the business? Hard to say, but don't expect Mulally to disappear into retirement. Though he didn't ultimately take the top job at Microsoft, industry insiders expect to see him in another influential position - likely as a board director or even chairman of another company. (We say "another company" and not Ford because while Bill Ford may have stepped aside as CEO to bring Mulally on board in the first place, we don't see him giving up his chairmanship of the board also.)
Mulally has likely already lined up his next move, and could either announce what that move will be as soon as Ford confirms Mark Fields as his successor, or could wait awhile. Insiders speculate that he could leverage his transportation and aerospace experience into a position at General Electric or a major airline, his manufacturing expertise to benefit a company like Procter & Gamble or his management skills at a consultancy firm.

How Ford made its 2015 Ford Mustang safer for toupee wearers [w/video]

Ford is ready to tell the story of its 2015 Mustang Convertible, the can't-miss bits being the easier, quicker and quieter roof operation, a more robust roof build for a coupe-like cabin noise, more trunk space, better visibility and reduced in-cabin buffeting. The top release system has been completely redesigned with a single, center-mounted latch on the windshield frame instead of the dual latches of before. The driver can now release the roof without having to lean over into the passenger space, after which the top goes down fully automatically with the press of a button. Ford doesn't say how long it takes to stow, but it's apparently done in half as much time as before, so figure around 8 seconds.
The roof uses a five-bow structure, with the fabric outer and full inner headliner sandwiching ten millimeters of insulation. Detailing work on the top has eliminated "unsightly folds" in the corners when the roof is up and made it more compact when down; its Z-fold assembly is 6.7 inches lower than before at its highest point when put down. Ford says the new electric drive internals make less noise when in operation, and the fully-finished droptop look is achieved with snap-in caps that flank the rear seating and stow in the trunk when not in use (the outgoing Mustang's top was higher and the front when folded and always looked like it was catching air and creating drag).
The compact roof and newly independent rear suspension setup in back means liberated trunk space, 11.4 cubic feet ready to swallow golf bags and tourist swag. You can read a lot more about it in the press release below, check it out in the short video of running footage and learn about the aerodynamic improvements made to the entire Mustang lineup that decrease drag and increase fuel economy.

Ford 3D-printing Mustang out of chocolate and candy for Valentine's Day

Is your beloved in love with the new 2015 Ford Mustang? Do they like chocolate (that's a trick question - everyone likes chocolate)? Are they a bit of a futurist? Then this Hallmark holiday, you need to get them this Ford Mustang, 3D-printed in sweet, delicious chocolate.
Ford is teaming with 3D Systems' Sugar Lab in LA to produce the super-accurate pony car confections in both chocolate and sugar candy varieties. The process kicked off with a CAD rendering of the 2015 Mustang, which was then programmed into the 3D printer. After a bit of work from the machine, a four-inch long, two-inch tall Mustang was the result. Why the tieup with 3D Systems, though?
"We wanted to create something fun to show that while 3D printing made these edible Mustangs, manufacturing-level 3D printing was used in the development of Ford's all-new sports car," said Paul Susalla, Ford's supervisor of 3D printing.