1963 Ford Fairlane Sports Coupe Survivor on 2040-cars

Auto blog

Ford trademarking 'Mach 1,' possibly for Mustang

A legendary name might be accompanying the redesigned, 2015 Mustang when it finally makes its world debut - Mach 1. Stumbled upon by the team at Ford Authority, the Mach 1 title was found in a trademark filing with the US Patent and Trademark Office, and would revive a name last used on the fourth-generation, 2003 Mustang.
While the the 2003 vintage was well and good, the Mach 1 is really remembered for a three-year run from 1969 to 1971 - it's best to just forget the emissions-choked 1972 to 1978 Mach 1s - when power output ranged from a modest 250 horsepower with the two-barrel, 351-cubic-inch Windsor V8 to "375 hp" (actual output was rumored to be well north of 400 horsepower) with the righteous, 429-cubic-inch Super Cobra Jet V8.
What does the title hold for the sixth-generation Mustang? It's tough to say. The fanatics at Ford Authority seem to think Mach 1 could take the place of the Shelby GT500 at the top of the Mustang hierarchy, which sounds like a valid argument. At the same time, we could see the SVT Cobra moniker returning for the flagship model, and the Mach 1 doing battle with the Chevrolet Camaro Z/28 (unless the Boss 302 were to return). Confounding things is the historical precedent - the Mach 1 was responsible for the death of the Mustang GT in 1969, so it might make sense as a volume performance model.

2015 Ford F-150 shaves 700 pounds, adds 2.7-liter EcoBoost [w/video]

The Ford F-150 is one of the best selling vehicles on the planet. Considering that, one can imagine that when it comes time for a redesign, there are hardly any half measures. For its lucky thirteenth generation, Ford has gone all-in on the single most important vehicle in its portfolio, redesigning it from the ground up.
The big news is the F-150's new, lightweight, Atlas-inspired body. Ninety-three percent of that new body is made from a sort of aluminum alloy not unlike what the US military uses in its M2 Bradley fighting vehicles and Humvees, and it accounts for up to 70 percent of the F-150's 700-pound weight reduction. As a side benefit, the aluminum body should prove more resistant to dents and dings. Built Ford tough, indeed.
If you're wondering where the other 30 percent of that 700-pound weight loss went, 8.5 percent (60 pounds) came from the increased use of high-strength steel (up from 23 percent to 77 percent) in its ladder-box frame. Ford claims this steel is comparable to some of the heavy duty pickups used by its competitors, with a PSI rating of 70,000.

Ford opens the doors on its Swedish rally skunkworks

It's always amazing to see how different kinds of racecars are made. Formula One racers are often constructed in modern architectural marvels that hint at some of the cutting-edge technology going into the racing. Conversely, rallying is all about sliding around on a varied course as fast as possible, but it often leaves a vehicle caked in mud. So it makes some sense Olsbergs MSE, or simply (OMSE) rally car shop in Nynashamn, Sweden, shows technological sophistication in a more down-to-earth setting. It builds Ford Fiesta ST racers for Global Rallycross there, and this new video gives viewers a tour through the work.
Former rally driver Andreas Eriksson runs OMSE. These days instead of racing, he and the company's 46 employees are building Ford racers from scratch. A ton of work goes into constructing each one, and according to Eriksson, it takes 400 hours to complete each body. At times, things are so busy that some of the technicians live in the shop in apartments that are on premises. There's even a restaurant to keep them fed. Sadly the dyno room is empty during this visit, though.
By the time OMSE is done, a rallycross car might resemble a Fiesta ST on the outside, but as you see in the video, it's a completely different beast underneath. Check out the work it takes to build one of them, and scroll down to read more about it in the official release.