1929 Model A Roadster Replica /1983 Camelot on 2040-cars
Brooklyn, Michigan, United States
1983 CAMELOT ROADSTER CAR RUNS AND DRIVES WITH ONLY 638 MILES 2.3 L 4CYL 4 SPEED STICK . ALL LIGHTS AND SIGNALS WORK, BRAKES AND EXHAUST IS GOOD, NO RIPS OR TEARS IN TOP OR INTERIOR , AM FM RADIO AND HAS SIDE CURTAINS, RACK AND PINION STEERING FRONT DISK BRAKES WITH RUMBLE SEAT
|
Ford Model A for Sale
- *** 1930 ford model a roadster ***
- 1931 model a slant window 4 door sedan
- 1931 ford model a hot rod rat rod hotrod ratrod bagged air ride custom lead sled(US $35,000.00)
- 1931 ford model a coupe(US $25,000.00)
- 1929 ford truck pickup model a
- Gorgeous 1929 ford model a, made to tour, 3 speed, overdrive, hydraulic brakes
Auto Services in Michigan
Wohlford`s Brake Stop ★★★★★
Wilder Auto Service ★★★★★
Valvoline Instant Oil Change ★★★★★
Trend Auto Sales ★★★★★
Transmission Authority ★★★★★
The Collision Shop ★★★★★
Auto blog
How Ford made its 2015 Ford Mustang safer for toupee wearers [w/video]
Fri, 28 Feb 2014Ford is ready to tell the story of its 2015 Mustang Convertible, the can't-miss bits being the easier, quicker and quieter roof operation, a more robust roof build for a coupe-like cabin noise, more trunk space, better visibility and reduced in-cabin buffeting. The top release system has been completely redesigned with a single, center-mounted latch on the windshield frame instead of the dual latches of before. The driver can now release the roof without having to lean over into the passenger space, after which the top goes down fully automatically with the press of a button. Ford doesn't say how long it takes to stow, but it's apparently done in half as much time as before, so figure around 8 seconds.
The roof uses a five-bow structure, with the fabric outer and full inner headliner sandwiching ten millimeters of insulation. Detailing work on the top has eliminated "unsightly folds" in the corners when the roof is up and made it more compact when down; its Z-fold assembly is 6.7 inches lower than before at its highest point when put down. Ford says the new electric drive internals make less noise when in operation, and the fully-finished droptop look is achieved with snap-in caps that flank the rear seating and stow in the trunk when not in use (the outgoing Mustang's top was higher and the front when folded and always looked like it was catching air and creating drag).
The compact roof and newly independent rear suspension setup in back means liberated trunk space, 11.4 cubic feet ready to swallow golf bags and tourist swag. You can read a lot more about it in the press release below, check it out in the short video of running footage and learn about the aerodynamic improvements made to the entire Mustang lineup that decrease drag and increase fuel economy.
These horribly misguided front-drive design studies nearly became the Mustang
Fri, 08 Nov 2013As we eagerly await the unveiling of the all-new sixth-generation Mustang, Ford has been giving us some great information over the past few months showing what has gone into shaping its venerable pony car. As many changes as the Mustang has gone through in its 50 years, though, it appears the fourth-gen model played a decisive and pivotal role in the car's future.
As is part of Mustang lore, the front-wheel drive Ford Probe was originally developed as a next-generation Mustang in the Eighties before cooler heads prevailed. The Blue Oval has just released a handful of images showing how bad things could have been - including a full-scale clay model of a front-wheel-drive Mustang (shown above). Fortunately, the FWD Mustang plan was scrapped and Ford went to work designing a rear-wheel-drive replacement for the Fox Body Mustang, with three design studies making it far enough to become full-scale models. These include the soft "Bruce Jenner" Mustang, the over-the-top "Rambo" Mustang and the middle-ground "Arnold Schwarzenegger" Mustang, which finally became the basis for the 1994 'Stang.
By early 1991, the design language of the fourth-generation Mustang had been worked out, and the rest, they say, is history. Scroll down for the fascinating press release telling the story of the fourth-gen Mustang, and be sure to check out the gallery of horribly misguided sketches and various design studies that were all on the table in the late 1980s.
Toyota fears supplier pressure in Australia with GM pull out
Wed, 11 Dec 2013With Ford and General Motors both announcing an end to production in Australia, the country's auto industry is in a bad way. With the exit of two big players, there's increased concern that a third Australian manufacturer, Toyota, will be forced out, as well.
"We are saddened to learn of GM Holden's decision. This will place unprecedented pressure on the local supplier network and our ability to build cars in Australia," Toyota Australia said in a statement. The GM closure of Holden production will be the direct end to 2,900 jobs, but will also force a dramatic reduction in the size of the country's supplier network, as there will simply be fewer cars to build.
In the same statement, Toyota Australia said it would work with suppliers and local government to figure out whether continuing production Down Under was even feasible. According to Automotive News, a representative for the Australian Manufacturing Workers' Union told reporters it was "highly likely" that Toyota would also close up shop within the next few years.