1926 Ford Model T Coupe Runs And Drives on 2040-cars

Auto blog

2015 Ford Mustang EcoBoost

Earlier this week, Ford invited us to Charlotte, NC, to ride in an all-new 2015 Mustang fitted with its turbocharged 2.3-liter EcoBoost four-cylinder. It's the first forced-induction, four-cylinder ponycar for the Blue Oval since the sun set on the 1986 Mustang SVO. We jumped at the opportunity, as only a handful of people have ever been in the passenger seat of this new car, and most automotive media won't get as close as we did until this fall.
As we revealed in our Deep Dive, Ford will slot this new turbocharged four as premium powerplant between its naturally aspirated 3.7-liter V6 and the naturally aspirated 5.0-liter V8. At last mention, the automaker said the direct-injected, all-aluminum engine will develop 305 horsepower and 300 pound-feet of torque, returning the best fuel economy of the three powerplants in the process. History buffs will note that those figures are appreciably stouter than the 200 horses and 240 lb-ft that the '86 SVO realized out of the same displacement, and the latter's figures were hugely impressive at the time. On paper, the new EcoBoost four looks to be a good fit for most owners who want to balance performance with efficiency - we were eager to see how it felt from the passenger seat.
Riding Notes

How Ford made its 2015 Ford Mustang safer for toupee wearers [w/video]

Ford is ready to tell the story of its 2015 Mustang Convertible, the can't-miss bits being the easier, quicker and quieter roof operation, a more robust roof build for a coupe-like cabin noise, more trunk space, better visibility and reduced in-cabin buffeting. The top release system has been completely redesigned with a single, center-mounted latch on the windshield frame instead of the dual latches of before. The driver can now release the roof without having to lean over into the passenger space, after which the top goes down fully automatically with the press of a button. Ford doesn't say how long it takes to stow, but it's apparently done in half as much time as before, so figure around 8 seconds.
The roof uses a five-bow structure, with the fabric outer and full inner headliner sandwiching ten millimeters of insulation. Detailing work on the top has eliminated "unsightly folds" in the corners when the roof is up and made it more compact when down; its Z-fold assembly is 6.7 inches lower than before at its highest point when put down. Ford says the new electric drive internals make less noise when in operation, and the fully-finished droptop look is achieved with snap-in caps that flank the rear seating and stow in the trunk when not in use (the outgoing Mustang's top was higher and the front when folded and always looked like it was catching air and creating drag).
The compact roof and newly independent rear suspension setup in back means liberated trunk space, 11.4 cubic feet ready to swallow golf bags and tourist swag. You can read a lot more about it in the press release below, check it out in the short video of running footage and learn about the aerodynamic improvements made to the entire Mustang lineup that decrease drag and increase fuel economy.

Ford cleans up painting process with cameras

Knowing how the bacon gets made rarely entices us and, in the same vein, the same usually goes for knowing about how new cars get painted. But in both instances, however, quality - or a lack thereof - is instantly obvious. In terms of the latter, Ford is showing off its new paint quality process with 3D Dirt Detection Technology to find imperfections in vehicle paint more easily and more quickly.
This process - being performed on the F-150 SVT Raptor above - uses 16 computer-controlled cameras to create a three-dimensional model (inset) of the vehicle to detect flaws in the paint including dirt particles, which can then be buffed out manually. Ford says this new technology cuts down on time spent looking for paint flaws and gives workers more time to correct those that are discovered.
Currently, Ford only uses its 3D Dirt Detection Technology system at three factories (the Dearborn, MI facility, along with those in Louisville, Kentucky and Valencia, Spain), but it will soon spread to five more plants in North America. Ford has released a video and press release for this innovative and unexpectedly interesting process, both of which are posted below.