Find or Sell Used Cars, Trucks, and SUVs in USA

1937 Ford Truck Pickup Rat Rod on 2040-cars

US $7,000.00
Year:1937 Mileage:999999 Color: Patina /
 Patina
Location:

Billerica, Massachusetts, United States

Billerica, Massachusetts, United States
Transmission:C4
Body Type:Pickup Truck
Vehicle Title:Clear
Engine:1971 Ford 302
Fuel Type:Gasoline
For Sale By:Private Seller
Year: 1937
Number of Cylinders: 8
Make: Ford
Model: Other Pickups
Trim: Patina
Drive Type: Automatic
Mileage: 999,999
Disability Equipped: No
Exterior Color: Patina
Warranty: Vehicle does NOT have an existing warranty
Interior Color: Patina
Condition: Used: A vehicle is considered used if it has been registered and issued a title. Used vehicles have had at least one previous owner. The condition of the exterior, interior and engine can vary depending on the vehicle's history. See the seller's listing for full details and description of any imperfections. ... 

Here we have a 1937 Ford Pickup on a homebuilt boxed frame - z'd rear end. It is powered by a 1971 Ford 302 out of a Torino with a 1974 Ford Mustang C4 transmission.  I have no title for the vehicle - most states don't require you to have one, just a bill of sale for such an old truck (It has a # stamped into the cab but MA is too tough to get a title from) - or just drive her as is - this is what I've done! I've replaced the intake manifold, put on a new Edlebrock 650cfm carb, new water pump with new hoses, new electronic ignition with new wires, new radiator, new lines, new push rods, new aluminum valve covers, new tires and a new aluminum spun 10gal gas tank. It has an ez wire fuse box (lines need to be tightened up) with running oil pressure, amps, and temp guages. New lights (brake, head), high beams and horn. I've taken the truck to where it it is but have no time and have lost interest. Will start up and run but needs to be 'dialed in' - drops out sometimes when I shift it into drive. Truck is fun and gets tons of interest at local cruise nights, but I need something for the entire family. I'll be happy to try and answer any questions you have but I've listed just about everything I know about the gal. She's a rat, she's fun, and she needs a little love to finish her. All the work on her has been done by me. Good luck bidding, she is as is, where is. Buyer must pick up - I will not be responsible for shipping. A $500 non-refundable deposit is due within 24hours of auction end. I invite anyone who would like to check her out to set up an appointment to stop by - I will be available at request. Truck is for sale locally so I reserve the right to end the auction at any time. Thank you!

Auto Services in Massachusetts

Westgate Tire & Auto Center ★★★★★

Auto Repair & Service, Automobile Parts & Supplies, Tire Dealers
Address: 98 Westgate Dr, Monponsett
Phone: (888) 603-6146

Stewie`s Tire & Auto Repair ★★★★★

Auto Repair & Service
Address: 641 N Main St, South-Weymouth
Phone: (781) 963-7856

School Street Garage ★★★★★

Auto Repair & Service, Engine Rebuilding & Exchange, Auto Engine Rebuilding
Address: 27 School St, Waban
Phone: (978) 263-7393

Saugus Auto-Craft ★★★★★

Auto Repair & Service, Automobile Body Repairing & Painting
Address: 79 Bennett St, Lynnfield
Phone: (781) 780-2040

Raffia Road Service Center ★★★★★

Auto Repair & Service, Brake Repair, Auto Transmission
Address: 105 Raffia Rd, E-Longmeadow
Phone: (860) 749-0584

Quality Auto Care ★★★★★

Auto Repair & Service, Brake Repair
Address: 76 Ramah Cir N, West-Whately
Phone: (413) 789-3500

Auto blog

Ford 3D-printing Mustang out of chocolate and candy for Valentine's Day

Thu, 13 Feb 2014

Is your beloved in love with the new 2015 Ford Mustang? Do they like chocolate (that's a trick question - everyone likes chocolate)? Are they a bit of a futurist? Then this Hallmark holiday, you need to get them this Ford Mustang, 3D-printed in sweet, delicious chocolate.
Ford is teaming with 3D Systems' Sugar Lab in LA to produce the super-accurate pony car confections in both chocolate and sugar candy varieties. The process kicked off with a CAD rendering of the 2015 Mustang, which was then programmed into the 3D printer. After a bit of work from the machine, a four-inch long, two-inch tall Mustang was the result. Why the tieup with 3D Systems, though?
"We wanted to create something fun to show that while 3D printing made these edible Mustangs, manufacturing-level 3D printing was used in the development of Ford's all-new sports car," said Paul Susalla, Ford's supervisor of 3D printing.

Toyota Camry, Honda Civic inventories mounting as US automakers make inroads

Thu, 11 Jul 2013

Two of the hottest-selling cars in America aren't quite as hot as they used to be. The Toyota Camry and Honda Civic are both seeing dealer supplies increase in the face of renewed competition from the much-improved Detroit Three.
According to a report from The Detroit News, the Camry's dealer inventory is 15 days higher than its seasonal average, while the Civic is 25 days above average. Things aren't expected to get better for Toyota and Honda, as RBC Capital Markets analyst Joseph Spak marked the two Japanese offerings as "at risk for reduced output."
The Detroit Three, meanwhile, are seeing supplies dwindle as demand increases, especially for the Ford Fusion, which has seen an 18-percent increase in 2013 sales, and the Chevrolet Cruze, which was second only to the Camry in June 2013 sales.

Ford Shelby GT350 Mustang is a track-day weapon with 500 hp

Mon, 17 Nov 2014



Ford promises more than 500 horsepower and a torque peak above 400 lb-ft.
The wait is finally over. After months of spy shots, rumor and innuendo, Ford has officially pulled the wraps off its new Shelby GT350. Judging by the spec sheet and the promises being made - especially that the Shelby GT350 will be "an all-day track car that's also street legal" - the wait appears to have been worth it.