1953 Chevrolet 3100 5 Window Truck Pickup on 2040-cars
Marion, Ohio, United States
For sale is a 1953 Chevy Truck that I have been working on for qutie a while.
Truck has a 5.3L Chevy motor out of a 2006 truck, a matching 4l60E, and
with only 60,000 on the odometer. Brand new drive shaft built by Drive Line 1 out of Columbus, Ohio. Harness was bought from and tuned by
LSX4U.com out of Maine with the electronic throttle. Has a brand new
Tanks Inc. 16 gallon tank and sending unit, with a fuel pump to handle up to 600 hp, and
the supporting fuel regulator/filter from the corvettes. All fuel lines
and trans cooler line were ran with 6 A.N. line. 18x8 front and 18x9.5
rears Boss 338 Wheels, wrapped in Nitto Neo Gen tires. 10 bolt Non-Posi
Rear end with drum brakes. Front big 11.5" Disc brake kit with drilled
and slotted rotors. Mustang II front suspension from a mid 70's mustang.
New Champion 4 core radiator with 16 " fan and a built in trans cooler. Chassis mounted power brake
booster and master cylinder. 32" trans mount Lokar Shifter. Chrome tilt Column with
turn and hazards built in. Grant steering wheel. Manual steering rack
with borgenson joints and stainless steering shaft. New glass all the
way around except for in the doors. ( Do not have glass for those yet).
Frame has been POR-15 painted. Has a completely re-built seat with a
cream colored seat cover. Installed a full Ridetech air ride system.
This is not a cheap put together system, it was purchased directly from
Ridetech. The system has the dual compressors and large tank upgrade
along with the red billet valves. The mustang II Air-Ride set up is from
Ridetech also. The only thing not Ridetech is the rear bags. I used
larger Slam Specialties bags for a better ride. The truck still needs
Gauges, carpeted, doors put together, door glass bought, bed wood bought
and installed, and could use an alignment. I'm getting very busy and someone
else could finish this truck the way they would want too saving the
labor charges of me doing it. Ive got 100's of hours in fabrication and
install between the motor and air-ride. Asking 21,500 as is or will
finish with complete interior for 26,000. Thanks for looking.
On Jun-16-14 at 12:15:16 PDT, seller added the following information: Just left out that it has a brand new starter, alternator. The alternator mount and motor mounts were bought from dirty dingo. Very high quality pieces. On Jun-17-14 at 10:32:38 PDT, seller added the following information: I will add things as i remember them, The truck has all stainless steel lines other than the hard bends, which we used NIcopp line. The truck now has the front bumper on and headlights going in tonight. I will snag some more pictures tonight of the interior. On Jun-17-14 at 10:52:28 PDT, seller added the following information: I wanted the ground clearance so i didn't put the running boards on the ground. But if you would like too i have a step notch kit from gambino customs to go with it. As for the doors not being together, the ones that came with it were shot. I bought bare doors from kansas and they are 100% rust free. Just need new glass and everything else will need to be transferred over from original doors. Have decent door panels with steel frames to go along, new billet window crank, billet door opener, and billet door sill plates. All of those are polished. |
Chevrolet Other Pickups for Sale
- Super nice 1934 chevy pickup truck hot rod 327/350 4-speed(US $23,000.00)
- 1950 chevy pickup truck original patina make a rat rod or shop truck(US $2,950.00)
- 1955 chevrolet pickup 3100
- 1955 chevrolet pickup, chevy truck, lowrider, 1955, 1956, 1957(US $9,500.00)
- 1952 chevrolet truck 3100 350/350
- 1942 chevrolet 1 1/2 ton rack body truck
Auto Services in Ohio
Zehner`s Service Center ★★★★★
Westlake Auto Body & Frame ★★★★★
Wellington Auto Svc ★★★★★
Walt`s Auto Inc ★★★★★
Waikem Mitsubishi ★★★★★
Vin Devers- Auto Haus of Sylvania ★★★★★
Auto blog
Experimental mid-engine XP-819 Corvette going up for auction
Sun, 17 Feb 2013It seems to be commonplace that when a new Corvette is in development, rumors swirl about a possible mid-engine layout. As is the case of Chevy's most recent C7 Corvette, these rumors never pan out.
In any case, the idea for a 'Vette with an engine mounted behind the driver can probably all be traced back to a single car, the 1964 XP-819 prototype. Built as an "engineering exercise" back in 1964, the prototype was designed with a rear-mounted engine. History tells us that the idea of a rear-engine Corvette fizzled, and the XP-819 was eventually cut up into pieces and stored at a shop in Daytona Beach, FL.
After sitting for untold years, a restoration project started on the car, and while it isn't yet fully completed, the current owner of the car, Mid America Motorworks, will have the car on display at the 2013 Amelia Island Concours d'Elegance as a "driveable chassis" with hopes of having a fully completed car ready to bring to next year's show.
2014 Chevy Silverado, GMC Sierra full configurators truck in
Sat, 15 Jun 2013You can now put prices to your wildest option-sheet dreams of the 2014 Chevrolet Silverado and GMC Sierra. A microsite for the full-size pickup truck twins has been up since January, and now the full-blown configurator is live and ready to take your virtual orders. The only two chassis configurations available at the moment are the Crew Cab with either a short or standard bed - Regular and Double Cab versions will come later. In Silverado flavors that will run you $32,710 for the short box, $33,010 for the standard box, while the Sierra adds a $1,500 premium to both of those prices, and destination and handling for both models adds another $995.
Since these are American pickups the list of modifications is lengthy, but we added $11,450 in just two steps by starting with the Silverado Crew Cab and standard bed, then checking four-wheel drive and the LTZ Z71 package. Our final truck, resplendent in Brownstone Metallic paint, heated and cooled Cocoa/Dune perforated leather seating and tasty details like chrome recovery hooks, and engine block heater and LED cargo box lighting, rang up $57,285 at the candy store.
They'll be on dealer lots sometime this summer, so now's a good time to start practicing your box-checking.
Officially Official: Chevrolet replaces Daewoo name in Korea
Thu, 20 Jan 2011
Chevrolet Camaro in Korea - Click above for high-resolution image
There once was a time when Daewoo was one of the biggest companies in South Korea. It was larger than both LG and Samsung, and second only to Hyundai. But these days the name is all but gone.